Dual circuit master cylinder? - Reply to Topic
Have an account? Register

Forgot your password?

Forgot your username?

 

Reply to Thread

Post a reply to the thread: Dual circuit master cylinder?

Your Message

 

Send Trackbacks to (Separate multiple URLs with spaces)

You may choose an icon for your message from this list

Register Now

Please enter the name by which you would like to log-in and be known on this site.

Please enter a password for your user account. Note that passwords are case-sensitive.

Please enter a valid email address for yourself.

Where you live, Town\City\County etc.

Please enter your full name
This field cannot be edited once it has been completed other than via contacting the site admin. Please make sure the information is correct first time.

Log-in

Additional Options

  • Will turn www.example.com into [URL]http://www.example.com[/URL].

Topic Review (Newest First)

  • 10-05-2019, 22:17
    mygasser
    as an aside in that last pic the cylinder actually moves when the pedal is pressed (notice the 'bellows' are at the left) but you can mount the cylinder the other way round so only the pullrod moves and the cylinder is fixed. pretty sure that's what we did to be honest.
    neil.
  • 10-05-2019, 18:16
    chaley
    Cheers Neil,
    That makes perfect sense. Out with the tape, it’s a bit busy down there what with the silly engine setback.

    drseg, I tried that a while ago and although it stopped it was more than a bit scary, as in feck that was close

    Chaley
  • 10-05-2019, 17:26
    drseg
    whats the brakes like if you just remove the servo? back then they wernt VERY served on the jago geep they deleted the servo from escort mk 1 mk 2 brakes (m16 calipers) as apparently it locked the rears too easy on the shorter lighter kit car and without the servo it still could lock the brakes if pressed nott unreasonably hard (19mm or 3/4") even fitted a transit one when that was all I had to hand (25mm 1") and that would still lock up if pressed hard
  • 10-05-2019, 16:58
    mygasser
    this is the best i could find mate, these guys even put a nylon sleeve through the bellhousing for the pushrod to go through. you get the idea though, the cylinder mounts to the engine (we used the 2 lower mount bolts to attach a bracket) and the extended pullrod goes through the hole where the cable used to go and connects to the clutch arm. when the pedal is pushed the cylinder pulls like the cable would.
    neil.
  • 10-05-2019, 11:36
    chaley
    I’m pretty sure I’ve got it Neil, but a picture paints a thousand words

    Chaley
  • 09-05-2019, 08:02
    mygasser
    Yep that easy, except with your setup you need to pull forward so the cylinder mounts (usually) by the engine mount with the pull rod extended to go through the hole in the bellhousing where the cable would be to then attach to the clutch arm. Think that makes sense, I know what I mean. I can do a pic if you need it.
    Neil.
  • 08-05-2019, 22:11
    chaley
    Ooh that looks easy and a whole load cheaper than a throwout kit.
    Is it as simple as this or does it need the body supported as well?



    Questions questions

    Chaley
  • 08-05-2019, 21:34
    mygasser
    we do a wilwood 'pull' type slave cylinder i've used before when fitting type 9 boxes into old fords with hydraulic clutch pedal boxes. a simple bracket to mount it on the side of the engine in line with the clutch cable hole in the bellhousing and you get a lovely light clutch. plus no broken cables ever again.
    https://www.rallydesign.co.uk/produc...oducts_id=4080
    neil.
  • 08-05-2019, 21:09
    chaley
    Cheers Neil,
    That last one was the one I was looking at, but I need a cable clutch one.

    Chaley
  • 08-05-2019, 20:42
    mygasser
    you could use one of these under the floor with your existing pedal https://www.rallydesign.co.uk/produc...oducts_id=4045
    or for matching pedals either of these on the floor, maybe with the cylinders through the lower bulkhead?
    https://www.rallydesign.co.uk/produc...ducts_id=13604
    https://www.rallydesign.co.uk/produc...ducts_id=24101
    neil.
This thread has more than 10 replies. Click here to review the whole thread.

Posting Permissions

  • You may post new threads
  • You may post replies
  • You may not post attachments
  • You may not edit your posts
  •