chop top mk2 - Reply to Topic
Have an account? Register

Forgot your password?

Forgot your username?


Reply to Thread

Post a reply to the thread: chop top mk2

Your Message


Send Trackbacks to (Separate multiple URLs with spaces)

You may choose an icon for your message from this list

Register Now

Please enter the name by which you would like to log-in and be known on this site.

Please enter a password for your user account. Note that passwords are case-sensitive.

Please enter a valid email address for yourself.

Where you live, Town\City\County etc.

Please enter your full name
This field cannot be edited once it has been completed other than via contacting the site admin. Please make sure the information is correct first time.


Additional Options

  • Will turn into [URL][/URL].

Topic Review (Newest First)

  • 12-07-2020, 19:51
    if its a 2 wire sensor try swapping the wires over .
  • 12-07-2020, 16:01
    chop top mk2
    total no start today, i know this sounds stupid but its like it now has no rpm signal at all its like the wire has broke. i am going to check that wire with a meter on tuesday to see if there is any current running through it.
    i will ring steve tomorrow to see what he say,s and then go from there.
  • 12-07-2020, 14:03
    I've heard plenty of bad reports about Fitech, this is just another in a long list of them.

    Check the crank sensor - this is one of the most common issues.
  • 11-07-2020, 17:33
    a long shot that I came across on a k series rover that was still under warranty, would drive fine then suddenly run rougher and rougher till stopped dealer failed to find anything and it usually didn't play up was a mates wifes so after I'd experienced it, turned it off left a few secs and restarted running perfectly for a couple of minutes decided to check timing was ok and then suddenly as it misfired and spluttered and stopped, retarded retarded and retarded till it stopped, did it again and again looked under the exhaust manifold a loose nut on a support bracket rattling causing the anti knock sensor to retard the ignition till i9t wouldn't run and the rougher it ran the more it rattled and the more it retarded tightened it and problem disappeared, probably not but worth a quick check for anything loose
  • 11-07-2020, 14:22
    chop top mk2
    problem not sorted. it does not have any error codes but it will tick over for a bit then the rev,s go up to 1700 rpm then the engine stops.

    i dont know enough about them blackpopracing to start messing. i will ring steve again on monday and see what he says and take it from there.
  • 08-07-2020, 18:57
    Fitech supplied sensors are reputedly rubbish. Changing them out for GM ones can often fix the issues.
  • 08-07-2020, 18:23
    chop top mk2
    cheers neil,
    i think i have bigger problems, the fitech is not reading the rpm signal so after 5 mins of running engine just cuts out. it will restart but wont run. i have contacted steve where i got the fitech from and this weekend i will try a couple of things he has advised and i am hoping that will sort the problem.
    was making some reel progress , bit gutted to be honest .
  • 04-07-2020, 20:32
    that's a lot of jobs completed in 1 day, well done.
  • 04-07-2020, 17:37
    chop top mk2
    to day has been pretty good,
    had a little to do list and got through most of it.
    starter just hanging up on flywheel when started, sorted 3mm shim plate.
    turbo oil feed pipe leaking, filter come loose sorted.
    exhaust leaking, exhaust paste sorted.
    the cable for the boot lid after 3 years of working decided to not work, and with no access to the boot i had to cut out the panel between the wheel tubs to get access . i had all ready made one when i did the new gearbox tunnel covers so today i got it fitted sorted.
    painted and fitted the amp in the boot, sorted.
    steering column bracket, the bracket was 1/2" thick and caught your toe when the clutch was released so i trimmed it down to 1/4" thick and rounded the edges and its now sorted.
    just got the brakes and the clutch to bleed tomorrow as i feel theres still a bit of air in the system.
  • 21-06-2020, 17:50
    chop top mk2
    i know where your coming from 69 ford but i like the wings to appear to finish and the grill to fit inside if you know what i mean.
This thread has more than 10 replies. Click here to review the whole thread.

Posting Permissions

  • You may post new threads
  • You may post replies
  • You may not post attachments
  • You may not edit your posts