How to get a Pro Street Pop through BIVA - Reply to Topic
Have an account? Register

Forgot your password?

Forgot your username?

 

Reply to Thread

Post a reply to the thread: How to get a Pro Street Pop through BIVA

Your Message

 

Send Trackbacks to (Separate multiple URLs with spaces)

You may choose an icon for your message from this list

Register Now

Please enter the name by which you would like to log-in and be known on this site.

Please enter a password for your user account. Note that passwords are case-sensitive.

Please enter a valid email address for yourself.

Where you live, Town\City\County etc.

Please enter your full name
This field cannot be edited once it has been completed other than via contacting the site admin. Please make sure the information is correct first time.

Log-in

Additional Options

  • Will turn www.example.com into [URL]http://www.example.com[/URL].

Topic Review (Newest First)

  • 16-02-2020, 16:37
    Dan Boy
    Thanks a lot guys.

    Probably old news but I was looking here today and they have a lot of useful stuff on there.

    Car Builder
  • 16-02-2020, 16:19
    blackpopracing
    You don't need to tether the fuel cap if the key cannot come out of the lock when the cap is undone.
    The vent tube needs to go as high up in the car as possible before looping back down to exit under the car. That way the fuel cannot get high enough to leak out.

    Sent from my SM-A105FN using Tapatalk
  • 16-02-2020, 15:04
    28Chevy
    If you're running carbs and using a valve, be careful which type you use, the wrong type can act as a one way valve and lead to gradual pressure build up due to temperature changes when not being used. This can lead to your engine sump filling with petrol, as the pressure overcomes the carb valves. Don't ask how I know this :-(
  • 16-02-2020, 13:51
    kapri
    You don't have to tether though it is the simplest way .Optionally you can use a locking fuel cap where you can only remove the key in the locked position.

    Breather should be routed to outside the car and not so it exits over an exhaust . To prevent fuel loss you normally route the breather up and away from the tank before returning it down wards to atmosphere.

    Alternatively you can buy roll over valves that allow venting but seal , under petrol weight, to prevent fluid loss.
  • 16-02-2020, 13:43
    Dan Boy
    I actually have a couple of questions about your fuel tank assembly.

    Firstly, I wondered how you tethered your fuel cap and secondly, I am not getting where the fuel tank vent should be routed to and how you prevent fuel just coming out of the end of the breather pipe.

    Thanks, Dan.
  • 09-02-2020, 22:30
    blackpopracing
    Thanks Dan, that was the point of the thread. To try to de-mystify it all to show its not as bad as everyone thinks.
  • 09-02-2020, 15:01
    Dan Boy
    Been through this whole thread. What an adventure you have been on. I have a long way to go with my build but I am more reassured that I can get a car through the test after reading this.

    Congratulations.
  • 25-11-2018, 21:13
    mygasser
    hi mark,
    you're not the only one with a black paint obsession. check out the reflection on this barracuda https://www.forabodiesonly.com/mopar...134292/page-20
    neil.
  • 24-11-2018, 20:57
    blackpopracing
    They recommend keeping original light wiring away from the heatsinks but the wiring provided is ok on them. I dont think the heatsink gets any hotter than a halogen bulb so a plastic housing will be fine. The heat is only on the aluminium rear sinks themselves, the bulbs remain cold.

    Its the opposite way round to a std halogen - halogens get hot at the front & cold at rear - these are cold at front & hot at rear.
  • 24-11-2018, 18:14
    chaley
    Evening Mark, they do light the way very well! But do you think the ‘very hot’ would be too much for a plastic light housing?

    Chaley
This thread has more than 10 replies. Click here to review the whole thread.

Posting Permissions

  • You may post new threads
  • You may post replies
  • You may not post attachments
  • You may not edit your posts
  •