Dual circuit master cylinder? - Page 2
Have an account? Register

Forgot your password?

Forgot your username?

 
Likes Likes:  4
+ Reply to Thread
Page 2 of 2 FirstFirst 1 2
Results 11 to 18 of 18
  1. #11
    Official RnS Addict mygasser's Avatar
    Join Date
    Dec 2009
    Location
    faversham, kent
    Posts
    12,566
    Images
    514
    Post Thanks / Like
    mygasser is online now
    we do a wilwood 'pull' type slave cylinder i've used before when fitting type 9 boxes into old fords with hydraulic clutch pedal boxes. a simple bracket to mount it on the side of the engine in line with the clutch cable hole in the bellhousing and you get a lovely light clutch. plus no broken cables ever again.
    https://www.rallydesign.co.uk/produc...oducts_id=4080
    neil.
    need a job done on your project? i may be able to help.

  2. Likeschaley liked this post
  3. Remove Advertisements
    RodsnSods.co.uk
    Advertisements
     

  4. #12
    Grown up? Never!
    Join Date
    Apr 2009
    Location
    Norwich
    Posts
    2,072
    Images
    36
    Post Thanks / Like
    chaley is offline
    Ooh that looks easy and a whole load cheaper than a throwout kit.
    Is it as simple as this or does it need the body supported as well?



    Questions questions

    Chaley
    And on the 6th day Man created god.
    Tetanus

  5. #13
    Official RnS Addict mygasser's Avatar
    Join Date
    Dec 2009
    Location
    faversham, kent
    Posts
    12,566
    Images
    514
    Post Thanks / Like
    mygasser is online now
    Yep that easy, except with your setup you need to pull forward so the cylinder mounts (usually) by the engine mount with the pull rod extended to go through the hole in the bellhousing where the cable would be to then attach to the clutch arm. Think that makes sense, I know what I mean. I can do a pic if you need it.
    Neil.
    need a job done on your project? i may be able to help.

  6. Remove Advertisements
    RodsnSods.co.uk
    Advertisements
     

  7. #14
    Grown up? Never!
    Join Date
    Apr 2009
    Location
    Norwich
    Posts
    2,072
    Images
    36
    Post Thanks / Like
    chaley is offline
    I’m pretty sure I’ve got it Neil, but a picture paints a thousand words

    Chaley
    And on the 6th day Man created god.
    Tetanus

  8. #15
    Official RnS Addict mygasser's Avatar
    Join Date
    Dec 2009
    Location
    faversham, kent
    Posts
    12,566
    Images
    514
    Post Thanks / Like
    mygasser is online now
    this is the best i could find mate, these guys even put a nylon sleeve through the bellhousing for the pushrod to go through. you get the idea though, the cylinder mounts to the engine (we used the 2 lower mount bolts to attach a bracket) and the extended pullrod goes through the hole where the cable used to go and connects to the clutch arm. when the pedal is pushed the cylinder pulls like the cable would.
    neil.
    Attached Images
    need a job done on your project? i may be able to help.

  9. Likeskapri liked this post
  10. #16
    Rods 'n' Sods Junkie
    Join Date
    May 2015
    Location
    Birmingham
    Posts
    307
    Images
    2
    Post Thanks / Like
    drseg is offline
    whats the brakes like if you just remove the servo? back then they wernt VERY served on the jago geep they deleted the servo from escort mk 1 mk 2 brakes (m16 calipers) as apparently it locked the rears too easy on the shorter lighter kit car and without the servo it still could lock the brakes if pressed nott unreasonably hard (19mm or 3/4") even fitted a transit one when that was all I had to hand (25mm 1") and that would still lock up if pressed hard

  11. #17
    Grown up? Never!
    Join Date
    Apr 2009
    Location
    Norwich
    Posts
    2,072
    Images
    36
    Post Thanks / Like
    chaley is offline
    Cheers Neil,
    That makes perfect sense. Out with the tape, it’s a bit busy down there what with the silly engine setback.

    drseg, I tried that a while ago and although it stopped it was more than a bit scary, as in feck that was close

    Chaley
    And on the 6th day Man created god.
    Tetanus

  12. #18
    Official RnS Addict mygasser's Avatar
    Join Date
    Dec 2009
    Location
    faversham, kent
    Posts
    12,566
    Images
    514
    Post Thanks / Like
    mygasser is online now
    as an aside in that last pic the cylinder actually moves when the pedal is pressed (notice the 'bellows' are at the left) but you can mount the cylinder the other way round so only the pullrod moves and the cylinder is fixed. pretty sure that's what we did to be honest.
    neil.
    need a job done on your project? i may be able to help.

  13. Likeschaley liked this post
+ Reply to Thread
Page 2 of 2 FirstFirst 1 2

Quick Reply Quick Reply

Register Now

Please enter the name by which you would like to log-in and be known on this site.

Please enter a password for your user account. Note that passwords are case-sensitive.

Please enter a valid email address for yourself.

Where you live, Town\City\County etc.

Please enter your full name
This field cannot be edited once it has been completed other than via contacting the site admin. Please make sure the information is correct first time.

Log-in

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

    Similar Threads

    1. WTD Wilwood dual circuit master cylinder
      By pitsspecial in forum Stuff - WANTED
      Replies: 5
      Last Post: 09-03-2013, 20:32
    2. Single or Dual Circuit Master Cylinder ?
      By WB54 in forum Tech Discussion
      Replies: 9
      Last Post: 31-08-2011, 21:47
    3. 7/8th or 22mm Dual Circuit Master Cylinder
      By WB54 in forum Tech Discussion
      Replies: 7
      Last Post: 16-08-2011, 15:42
    4. Dual circuit Master cylinder.
      By 50AD3100 in forum Stuff - FOR SALE
      Replies: 0
      Last Post: 03-04-2011, 04:36

    Bookmarks

    Posting Permissions

    • You may post new threads
    • You may post replies
    • You may not post attachments
    • You may not edit your posts
    •