Mustang II IFS on a Pop ? - Page 4
Have an account? Register

Forgot your password?

Forgot your username?

 
Likes Likes:  0
+ Reply to Thread
Page 4 of 5 FirstFirst ... 2 3 4 5 LastLast
Results 31 to 40 of 45
  1. #31
    Administrator blackpopracing's Avatar
    Join Date
    Apr 2009
    Location
    Slough
    Posts
    8,854
    Images
    1759
    Post Thanks / Like
    blackpopracing is offline
    here you go Si;


















  2. Remove Advertisements
    RodsnSods.co.uk
    Advertisements
     

  3. #32
    Official RnS Addict Roadrunna's Avatar
    Join Date
    Apr 2009
    Location
    Oldbury, West Mids
    Posts
    7,436
    Images
    768
    Post Thanks / Like
    Images
    61
    Roadrunna is offline
    Cheers Mark.

    Do you know or speak to the person who built it ? If so, do you reckon there'd be any chance of getting some hub to hub measurements and some for the width of the crossmember & between the upper arms ?
    Meep Meep.
    My Intro

  4. #33
    Administrator blackpopracing's Avatar
    Join Date
    Apr 2009
    Location
    Slough
    Posts
    8,854
    Images
    1759
    Post Thanks / Like
    blackpopracing is offline
    Hi Si,
    Yes & yes, will get back to you soon.

  5. Remove Advertisements
    RodsnSods.co.uk
    Advertisements
     

  6. #34
    Administrator blackpopracing's Avatar
    Join Date
    Apr 2009
    Location
    Slough
    Posts
    8,854
    Images
    1759
    Post Thanks / Like
    blackpopracing is offline
    The Fatman Fabs measurement is 46" hub to hub, will get back to you with measurements fron the car above.

  7. #35
    Official RnS Addict Roadrunna's Avatar
    Join Date
    Apr 2009
    Location
    Oldbury, West Mids
    Posts
    7,436
    Images
    768
    Post Thanks / Like
    Images
    61
    Roadrunna is offline
    Just measured up the steering rack in the garage as it's not been adjusted since it was all assembled. The rack measures 46" between track rod ends.
    The current crossmember is 21" between chassis rails and was built for 2" wide box section.
    Rough guessurements reckons my front end was 52" hub to hub.

    Looks like I might be chopping a bit out the crossmember and rack
    Meep Meep.
    My Intro

  8. #36
    Administrator blackpopracing's Avatar
    Join Date
    Apr 2009
    Location
    Slough
    Posts
    8,854
    Images
    1759
    Post Thanks / Like
    blackpopracing is offline
    A few more for you Si,












  9. #37
    Administrator blackpopracing's Avatar
    Join Date
    Apr 2009
    Location
    Slough
    Posts
    8,854
    Images
    1759
    Post Thanks / Like
    blackpopracing is offline
    Here's a load more info for you Si, this should give you plenty to go on.


















  10. #38
    Official RnS Addict Roadrunna's Avatar
    Join Date
    Apr 2009
    Location
    Oldbury, West Mids
    Posts
    7,436
    Images
    768
    Post Thanks / Like
    Images
    61
    Roadrunna is offline
    Fantastic mate

    Those drawings are perfect

    Time to digest and then work out some other saft questions
    Meep Meep.
    My Intro

  11. #39
    Administrator blackpopracing's Avatar
    Join Date
    Apr 2009
    Location
    Slough
    Posts
    8,854
    Images
    1759
    Post Thanks / Like
    blackpopracing is offline
    Si,
    Forgot to put in, his hub to hub width is 46.25 inches.

  12. #40
    Official RnS Addict Roadrunna's Avatar
    Join Date
    Apr 2009
    Location
    Oldbury, West Mids
    Posts
    7,436
    Images
    768
    Post Thanks / Like
    Images
    61
    Roadrunna is offline
    Just measured all my setup and it's looking good. All his measurements match mine - 8 1/2 inches. Bottom arms are the same length and mounting points on the crossmember make everything tally up once i've snipped it

    Looks like we could be on to a winner
    Meep Meep.
    My Intro

+ Reply to Thread
Page 4 of 5 FirstFirst ... 2 3 4 5 LastLast

Quick Reply Quick Reply

Register Now

Please enter the name by which you would like to log-in and be known on this site.

Please enter a password for your user account. Note that passwords are case-sensitive.

Please enter a valid email address for yourself.

Where you live, Town\City\County etc.

Please enter your full name
This field cannot be edited once it has been completed other than via contacting the site admin. Please make sure the information is correct first time.

Log-in

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

    Similar Threads

    1. My 54 pop project
      By Tattooaddict in forum The Garage
      Replies: 17
      Last Post: 07-07-2011, 07:12
    2. Mk 2 Mustang IFS geometry ,,
      By Tuggy in forum Tech Discussion
      Replies: 1
      Last Post: 05-01-2011, 18:58
    3. Mustang IFS
      By Epy in forum Stuff - WANTED
      Replies: 0
      Last Post: 07-11-2010, 21:53
    4. various,model t/mustang/pop...
      By TOETAG in forum Stuff - FOR SALE
      Replies: 14
      Last Post: 02-04-2010, 23:19
    5. ford pop handbrake
      By sqweaka in forum Tech Discussion
      Replies: 8
      Last Post: 22-04-2009, 20:00

    Bookmarks

    Posting Permissions

    • You may post new threads
    • You may post replies
    • You may not post attachments
    • You may not edit your posts
    •