Rods 'n' Sods - UK Hot Rod & Street Rod Forums banner
1-20 of 39 Results
  1. The Garage
    So after lots of lurking and learning I managed to source a half engine from the states for my project car. It's a 1974 four bolt main on standard bores and crank, and at first glance hadn't been run in a long long time. After its arrival I soon found why it had been pulled; head gasket...
  2. Stuff - WANTED
    Ideally I am after a non fuel injection running Chevy 305 that I can see running. However will consider 305,350 or a complete car that I can cannibalize if at the right price.
  3. Traders - For Sale / Services - CLOSED
    TWO ENGINES FOR SALE 454 Chevrolet V8, completely rebuilt, rebored, crank ground etc etc 350 Chevrolet V8, completely rebuilt, rebored, crank ground etc etc Can be supplied as turnkey as you want. Full build photo's at American V8 Engines & Gearboxes, Classic American Cars, Norwich, Norfolk...
  4. Stuff - FOR SALE
    GM Performance Parts' ZZ4 intake manifolds are designed for use on all ZZ series 350 HO engines, but can be used on any small block Chevrolet through 1986. They're about .5 in. lower than an LT1 manifold, for better underhood clearance, and can mount either a standard-flange Holley 4-barrel or a...
  5. Stuff - WANTED
    I'm after a cheap mock up chevy 350 engine, doesn't need to be a runner - only need it for measurements - cheaper the better needs to be complete with heads,rocker covers,damper,water pump and pref a dizzy
  6. Stuff - FOR SALE
    Hi all 383 Chevy for sale, currently on ebay -Item 330425593204 Open to offers and will remove if anyone interested 350 - 2 bolt 3970010 block, plus 0.30, New Eagle crank & bearings New hypreutectic pistons, new rings, New Comp Cams 260H cam with new Sealed Power lifters Fully ported...
  7. Stuff - FOR SALE
    I have for sale the following parts. Comp Cam Solid Roller Cam 12-912-9 Lifters 818-16 Springs 954-16 Rev Kit 4000 Retainers 741-16 Super Locks 611-16 Lash Caps 621-16 Crane Roller Rockers 11752-16 Valve Train Girdle 11604-1 Cloyes Hex a Just Chain Set 9-3100A Bronze Distributor Gear All brand...
  8. Stuff - FOR SALE
    gm performace parts 350 ramjet crate motor 350bhp 9.4.1 comp hydraulic roller cam 1.6 roller rockers vortec heads hypereutectic pistons fordeged rods 3/8 bolts ecm wiring harness coil plug leads spark plugs fluidampr flexplate £2750 paul 07919211033
  9. Stuff - WANTED
    Wanted a Th 350 Auto Box For 85-90 Camaro must be working. Cheers :D
  10. Tech Discussion
    pulled the pan twice to try to cure the leak out of the gasket rail. Put on a new thicker gasket METICULOUSLY installed and still it leaks. I did not put sealer on gasket as I understand you are not supposed to. When the fluid drains down into the pan on turning off the engine it is going to be...
  11. Tech Discussion
    I need some help from some of you experienced sbc guys. Engine is a 350 sbc with HEI dizzy. Initial timing without vacuum advanced connected is 12* BTDC. Problem is , if I leave the vacuum advance disconnected the motor seems to run fine. However as soon as I reconnect the vacuum advance line...
  12. Stuff - WANTED
    need a one piece seal motor,will settle for a block and heads,etc...
  13. Tech Discussion
    Well I had always had in mind getting rid of the injection system on my van, it's under powered and gobbles fuel for the size of engine. Now I'm not arsed about the fuel economy, but there must be more horses in there! Now after a good chat with Eadys autos, simply swapping for carbs is a nono...
  14. Stuff - FOR SALE
    350 sbc for either blower or turbos standard bore block with billet 4 bolt caps new steel crank,rods and je pistons, edelbrook ported victor jnr ally heads. new roller cam jesel belt drive, 2 set roller rockers 1 set new, stud girdle full arp stud set, sump, rocker covers damper, heads stripped...
  15. Stuff - WANTED
    moved to for sale
  16. Stuff - WANTED
    wanted th 350 yoke to fit 57 chevy thanks chris
  17. Stuff - FOR SALE
    Buick 350 4 barrel td250 1976 5.7cc new water bump fitted reason for sale is that it won,t fit new kit car v.g.c can be seen running £500.00 o.n.o 07884090557
  18. Stuff - FOR SALE
    -------------------------------------------------------------------------------- Complete 350 cu in olds engine an autobox. Removed from a 1970's Cutlass, Bought from a good source for a customers car but remained unused by us. Needs a repaint but all there. £300 Please call 01993 845427 or...
  19. Tech Discussion
    Hi all, got a rebuilt 355ci/TH350 Chevy mill and after some basic start up settings. The mills been sat there for years since the rebuild and am now pooping it after seeing the horror stories of failed initial run ups with cam problems etc. I need this baby to start and run up without any...
  20. On Topic
    Reading about chevy small blocks being turbo'ed. Is it a HP thing if so surely a 572 BBC would do the job without the hassle???
1-20 of 39 Results