Second hand Holley HP 4150 mech secondary carb (650CFM) - list number 80541-2 These are on Real Steel for 850+VAT new

Hi Guys I have a Holley 4160 with the throttle cable roughly pinched onto the carbs throttle arm by a bolt and 2 washers. Not very nice and has no freedom of movement. I have been trying to source a simple cable end pivot arm with a small pinch screw for the cable but I have had no joy :(...

Holley 390 Carburettor + spacer/riser block + modified Rover p6 V8 inlet manifold + home made air filter (low profile). Been on a running car this week - £165 inc. delivery to Hot Rod Hayride.

Hi folks,I`m in a bit of a bind.I`ve skilfully managed to crack the top cover of the back carb on my Konsul . Its a Mikuni 30/32 DIDTA carb as fitted to a 1981 Mitsubishi Sapporo GSR(2L). This is a longshot cos they`re pretty rare but would appreciate any leads to find one(even a krap one)...

ive got for sale a 390 holly with a secondry metering plate (plate not fitted and is new ) £125 came of running car about 12 months ago. also got a 600 double pumper that came of a car but it looks incomplete so im going to sell it as spares so theres no hassle. 07946520677 cheers maz

The engine in my Mk1 Capri 3.5V8 is knackered so I'm on the lookout for another. Have bought two off e-bay which turned out to be non-runners so I need one that I can see running before I pay. - Will also consider a whole car as long as the engine is good. Thanks Paul

Yes,its me again! My Pilot carb was not right,so i had a spare which was fitted,and although it is much better,its still not right. So has anyone got a known to be guaranteed good carb going spare to fit my 21 stud flathead,Its the Ford 94(?think thats right,cant remember right now,new to this...

Hey all, i have a rochester dual jet carb (definately not the quad barrel) code is M2ME i think? sat on my 3.8 v6 Buick boat anchor of an engine, it works fine apart from at extreme angles, (bearing in mind my car has hydraulics suspension) When the car hits extremes with the angles the engine...

I've got an Edelbrock 1405 carb and when the engine is running, petrol slowly drips out of where the throttle rod goes into the carb. I've taken the rod out assuming that there would be a duff seal but there isn't a seal at all! What do I do now? The rods wobbles slightly in the hole which I...

ebay http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=200465231874&ssPageName=STRK:MESELX:IT Anyone on here wants it £100 plus £10 post or you can collect.

Holley double pumper for sale, believe it's a 600cfm. Bought in error as it's too big for my motor. Should suit a small block or a hotter/bigger capacity Rover V8 etc. Carb number: 4791. Pics: Bought in perfect working order, never ran it but I have no reason to believe it's anything other...

I picked this up off this fine forum a month or two go but I've decided to change my carb now so it's surplus to requirements. It's a Weiand scoop, comes with Weiand filter and it's for a single round-top carb like Holley, Offy etc. It's in great condition. I payed £50 for it so that's...

holley 650 double pumper and pair of rear coilovers approx 13" 300lbs springs anyone got these going spare ?

id like a twin carb set up for my 140j pleeze or any go faster bits and pieces that any 1 has ytat would fit this fantastic piece of japaneese engineering by the way im skint so if youd like to give things away and you live near north wales that would be fantastic:tup:i know im a cheeky git but...

Advertising this for my mate Polished, converted Rover inlet manifold complete with fully rebuilt Webber 38 DGAS and brend new Edelbrock 14" chrome air filter, all throttle linkages etc bolt it on and off you go, these carbs give plenty power for the street and return good MPG on a rover. £130...

Hi all im looking for a triple carb setup for a mk2 ford zephr if anyone could help cheers mark

Twin SU Carbs and Manifold.......£65.00 Alternator...............................£20.00 Radiator.................................£20.00 Servo....................................£20.00 For more information & pics please phone danny on 07949661135.

I'm looking for a carb to run my standard Rover V8- A Holley 390 or something like that. Also an inlet manifold for the Rover V8, a suitable electric fuel pump and (not so urgently) a bug catcher too. Would be nice if the carb is from a Rover and ready to bolt on without too much messing...

ive been making these for a few people but would like some unbiased input. simple realy, 1) has anyone used them and got a good performance increase? 2) what would you think is the optimal thickness? 3) are insulating ones better than aluminium? i ask this as ive never used them but made a...

I'm after a 390 holley carb & edelbrock performer manifold for my 3.5 rover thanks Djstaffy