Rods 'n' Sods - UK Hot Rod & Street Rod Forums banner
1-18 of 18 Results
  1. Stuff - FOR SALE
    Crank #3932442 SBC £ 50-00 collection from luton / milton keynes
  2. Tech Discussion
    hi all i need a crank puller to get the belt pulley of the crank so i can carry on striping my engine think the tool would be universal but its for ford 4bolt thanks
  3. Stuff - WANTED
    i need a 289 crank and rods or if need be a shortblock for a 66 mustang just imported any help greatly appreciated email [email protected]
  4. Stuff - FOR SALE
    Done block resized rods. ground crank, new cam bearins installed nice. £1200. Russ 07980 416785
  5. Tech Discussion
    Hi all. I know I asked a similar question to this a few months ago asking about changing the rear crank seal on a sbc whilst the engine is in situ. To be honest I haven't gotten round to changing it yet hence the new enquiry. When changing these seals do they have to be replaced like for like...
  6. Tech Discussion
    On a slight follow up to my last query i do seem to have a bit of an oil leak. A patch of oil has appeared under the car since it was last used last month and upon inspection there seems to be oil covering various parts of the sump, which is a chrome aftermarket type, and it seems to sprayed...
  7. Traders - For Sale / Services - CLOSED
    Early Chevy 283 HI-PO block cast in Canada..... very thick walls , block tanked & magnafluxed , STD bore. THIS BLOCK CAN BE BORED TO 327cid dia and was by GM Here is casting # & ID of block #3789817 GM 327 / 62-65 Passenger,Chevelle,Truck Sm journal Also 283 FORGED crankshaft STD/STD. Here is...
  8. Freebies
    I have a Mopar 318 block and crank and heads I belive this is standard bore this is in ashford Kent All I would like for this is a small amout that I will donate to rods n sods 07773769478
  9. Tech Discussion
    hi all im trying to get hold of some flywheel(flex plate) to crank bolts.i havent got any old ones . its to fit a borg warner 35 auto box to a rover sd1. ive tried rimmer bros and rpi.with no success yet.:shake: if anyone know s what size i need or where i can get some from please can you...
  10. Tech Discussion
    Today I measured the endfloat on the crank in a Rover V8 I'm building. It's 0.010" which is too much - it's supposed to be 0.004" to 0.008". I positioned a dial guage on the snout of the crank and levered the crank forwards and then backwards. The dial swept out 0.010" from being pushed forwards...
  11. Stuff - WANTED
    need a one piece seal small block crank to fit a 305..ta.. rods and pistons may gayvan stuff as the pistons are for a z28 camaro.(flat top type)
  12. Stuff - FOR SALE
    For sale, for Ford flathead engine: This assembly is in very nice condition, taken from a low-miles 1987 French flathead. Crank, rods and pistons all in great condition, all well lubed and span freely in the block 4" stroke x 3 3/16" bore equals 255 cubic inches - same as late model Mercury...
  13. Stuff - WANTED
    Wanted 1980 231 Evenfire Pontiac /Buick crank or complete engine considered.
  14. Stuff - FOR SALE
    Aluminium rads to fit Ford/Mopar engines, I have a choice of 26,28 or 31" wide, all are 19" tall. £140 each. Aluminium rads to fit Chevy motors, 26 x 19 only. £160 each. All the above are claimed to cool up to 800hp engines, 2 rows of 1" tubes. Aluminium `32 style rads, I have stock height Ford...
  15. Stuff - WANTED
    I need a serpentine crank pulley for a 4.3 V6 chevy, 6" diam, 3" dish. Mines very rusty. Anyone got one??
  16. Freebies
    I have a Stock SBC 350ci Crank, could do with a polish or grind. Take it away ! Sussex Area.
  17. Stuff - WANTED
    Alloy bottom pulley wanted for small block ford V8. Four bolt holes, grooved for V belts. Don't care how many grooves. Ta.
  18. Stuff - FOR SALE
    First Item!!!!!!!!!!!! Crank is good, std/std, looking for £70 ono PM or call Ian on 07710 989559
1-18 of 18 Results