Rods 'n' Sods - UK Hot Rod & Street Rod Forums banner
1-19 of 19 Results
  1. Stuff - FOR SALE
    this is my old dizzy from my camaro, its marked as a delco remy coil comes with 8mm silicone leads about 2 years old. not hard or cracked £30 plus delivery delivery about 10quid cheers craig
  2. Tech Discussion
    Got a vacuum advance Mallory dual point in my sons coupe thats making a steady clicking noise, like the rotor arm's hitting the cap [bit like a elec fuel pump noise]. any one know what it could be? taken cap off and looks fine
  3. Stuff - WANTED
    Dizzy needed for a early 80's 318 dodge motor thanks mike.
  4. Stuff - FOR SALE
    like it says on the tin . rv8 dizzy unused . £65 posted
  5. Stuff - WANTED
    hello all im after an working early type leccy dizzy +amp module +coil, set up for a 2ltr pinto sohc .can anyone help ? so i can change from points . cheers wayne
  6. Tech Discussion
    Hello everyone im in need of your brain cells again . i want a leccy dizzy for my 2ltr pinto (bosch dizzy ). yes its only a pinto but in my consul its a new lease of life .i know early sierra was a quick option ,but that type of dizzy i cant find and i dont fancy to much messing...
  7. Tech Discussion
    have twin point mallory dizzy on a 302 do i need to buy mallory specific cap ,rotor and points or do others fit
  8. Stuff - WANTED
    unilite dizzy cap on a 302 v8 thanks
  9. Stuff - FOR SALE
    small block mopar dizzy's mallory dual point with good points rotor and cap £55ono all plus post or will take to essex swap meet
  10. Stuff - FOR SALE
    hi all i have an old Accel dual point dizzy for Ford 351c, 429/460, there isnt any cap but still has the points in it, all i want is £10 + post.. :tup: jim
  11. Traders - For Sale / Services - CLOSED
    New in the box E/W USA SBF electronic dizzy / small cap , vaccum advance , load & lite complete. 110 GBP to your door UK. Regards Daryl
  12. Stuff - WANTED
    I need a small type (space saver, if you like) dizzy for my sbf ford. I'v fitted a twin carb tunnel ram and now my HEI dizzy dosent fit. If you have an entire ignition setup, with dizzy included, all the better, but most of all I need a small dizzy. Anything at all considered. Cash payed...
  13. Tech Discussion
    Hi, I've just unstalled a 305 out of an 80s Firebird and I'm confronted by a four pin connector. Anyone know what each pin is or where I can find out? Cheers, Gary
  14. Tech Discussion
    bit basic but whats the best way to install a dizzy in a 302. dont something have to line up when one piston is at a certain point. setting timing using a vac gauge. reading the net some say you use it at idle but others say set it up with engine at 2000 rpm. can it be set up at idle as i...
  15. On Topic
    Hi, will a P6 RV8 dizzy (with points) with gear drive fit my SD1 motor.? or are there "other" differences ? My elec. ign is playing up & I need to get the whole thing sorted !:sniff: Ta John
  16. Stuff - FOR SALE
    Pinto bits provisionally sold. Pinto electronic distributor, with section of harness and control unit. Good upgrade from points. needs a clean. £25. Set of NGK APR6FS new plugs, in box, and two oil filters, wix brand in box, All suitable for Pinto. £10 lot. £30 for all. Prefer drop off at...
  17. Tech Discussion
    just wodered if any of you have used a mallory magnetic breakerless dizzy,bought a car for the motor,heard it runnin,mint,so i used the as new dizzy,new mallory coil, followed mallory wiring diagram, just can,t get a spark on the plugs,i have give up now,jim351 is selling me another dizzy, but...
  18. Tech Discussion
    I need to replace the knackered dizzy cap on my Rover V8 Mallory dizzy. The wear pattern shows that the rotor arm's not meeting the contacts in the cap properly, so it's probably made in China with little attention to accuracy. I've heard that some folk with this dizzy use a different make of...
  19. Tech Discussion
    Is there a special way to wire these or a special tacho required ? The HEI has a 2 pin take off for the tacho but most standard tachos only use 1 pulse wire to the coil. HELP!!
1-19 of 19 Results