Rods 'n' Sods - UK Hot Rod & Street Rod Forums banner
1-13 of 13 Results
  1. Stuff - WANTED
    Anyone got a ford 9" or 8.8 rear axle. Looking for a 63" or 65.25 (or there abouts) WMF to WMF. Leaf spring, drum brakes, 5x5.5" pcd would be great (econoline, F150 etc). I have a 1972 E200 econoline with a 68" axle but want to fit my 10x15's under the standard arches.
  2. Stuff - WANTED
    Hi everyone, I'm looking for a pair of slot mags 15" or larger. At least 8" wide. I'd consider full set if that's what you have. I have a set of 15x10 slot mags with too much offset (very deep dish) for my van so could trade if required. 5 stud 139.7 or 5.5 inch pcd. Anyone?:D
  3. Stuff - WANTED
    Rather than fit narrower wheels to my gen 2 Econoline , another option for me is to fit a narrower rear axle, the econoline should have a 68". Anyone got a 9" ford axle, 65" (drum face to drum face)? I believe an early F150 70's is 65" A LSD would be bonus. :D
  4. Stuff - WANTED
    Hi Guys n Gals, I'm looking for some ford alloys for my Econoline. I currently have 10x15" with a 3" back space but need something similar but with more back space (less of a dish), so probably 10x15 with 5" back space or 9x15 with a 4" back space. My wheels stick out too far for use without...
  5. Tech Discussion
    Got my mechanic to take out my cooked 351w, so far it does not look too bad, sending it off to get a diagnosis on the Heads and Block so I'll know what's what next week. Looks like its worth replacing various bits whilst the engine is out, any suggestions for best practice on that? And more...
  6. On Topic
    I've done a search on here and the odd thread/post appears but not a lot really. These ugly little buggers are growing on me and the missus loves em too so looks like i'm in the market for getting my hands on one. Anyone have any real world experience of ownership/driving em over here? Are...
  7. Vehicles - WANTED
    Hi folks, does anyone have or know of any of the following 60's window vans for sale? • Dodge A100 • Ford Econoline/Falcon • Chevy Sportsvan Ideally I want something that is solid, rot free and mechanically sorted, correctly registered, MOT'd and ideally lowered as well. I'm not bothered...
  8. Stuff - WANTED
    its a 1982 E350:bigsmile:
  9. On Topic
    brother in law calls, his mates looking for a tow bar for a late model Econoline, needs to tow a caravan,............anyone any ideas, or is it stateside direct cheers
  10. Stuff - FOR SALE
    Econoline ford motor (235ci i think), straight 6 , turbod in the 80's , runs strong , complete with manual gearbox , old rochester carb inc came out of 1949 ford f1 replaced by 302 £300 ono spec sheet for motor available Also original motor from 59 ford f100 runs well cracked inlet...
  11. Stuff - FOR SALE
    firebird formula, loads left ,bare 305 v8,front clip, steering box,brakes,tilt column,16"alloys,back axle,most panels[no bonnet],dash,etcshell with v5c,also 87 econoline,injected 302,can be heard running,most parts available,burnt interior and o/s doors,phone for details,vehicles in poole...
  12. Stuff - WANTED
    Hi lads an lasses , im after a flywheel for a 67 ford econoline motor , straight 6 , the ring gear is 14 1/4 '' across and the internal diameter is 44mm approx , can anyone help me ? its for a motor going in Daves 59 f100 , the old starter chewed up the ringgear before the motor was swapped out...
  13. Vehicles - WANTED
    or maybe a van, 6 or v8, prefer a camper with pop top, anything out there Rod [email protected]
1-13 of 13 Results