Rods 'n' Sods - UK Hot Rod & Street Rod Forums banner
1-14 of 14 Results
  1. Tech Discussion
    Hi Guys I have a Holley 4160 with the throttle cable roughly pinched onto the carbs throttle arm by a bolt and 2 washers. Not very nice and has no freedom of movement. I have been trying to source a simple cable end pivot arm with a small pinch screw for the cable but I have had no joy :(...
  2. Stuff - WANTED
    sbc throttle linkage and cable wanted , the type that also holds the kick down cable for a th350 WHY ? Cheers Ash
  3. Stuff - WANTED
    Has anyone got one they want to sell? Thanks chaps Mark
  4. Stuff - WANTED
    Wanted urgently for my mate Frank a Rover V8 SU carb linkage which attaches to the inlet manifold. If you give him a text he'll phone you back Cheers Dave text Frank on 07737292624
  5. Tech Discussion
    following on from my wanted ad......can anyone supply me with either a photo or even better the link a holley carb on a rover v8 to the kick down cable? the cable on my pop only just reaches the rear of the l/h rocker has a clevis fitting on the end.....i need something to...
  6. Stuff - WANTED
    wanted...kickdown linkage to suit rover v8 powered pop with holley carb...i have cable fitted to gearbox just need to link it up somehow as its too short to reach carb........beleive i need brackets and rod linkage to carb?? or can i connect direct to throttle cable somehow??
  7. Stuff - FOR SALE
    Hurst Competition Plus Shifter for ford 4 speed top loader - Brand new and boxed part No. 3913180. Hurst Linkage for the above Shifter - Brand new and Boxed. Changing to 5 speed so no longer needed. £200 + postage [email protected]
  8. Stuff - WANTED
    Hi All, As it says above, I need the gear linkage cable or rods from a B&M click shift to the TH350 gearbox. Are these expensive new and does anyone know where I can get them, if not I would be happy with a good secondhand set. Cheers, Stu.
  9. Tech Discussion
    I discovered today that my car can be started in reverse due to wear in the linkage from the column shift to the gearbox. Not clever.... Rather than welding up worn holes & re-drilling I thought about replacing both rods with an adjustable rose jointed (rod-end) set up. Would M6 joints be...
  10. Tech Discussion
    Hi All, How easy is it to set up the linkage for the autobox? Is it possible to run a rod rather than a cable? If I shortened the linkage would this cause gear selection problems? Just trying to sort out a gearbox mounting issue with out having to cut the car up too much. All help is...
  11. Tech Discussion
    I'm re-assembling my mates '53 truck and although I'm putting it back as taken apart it doesn't look right to me . The shifter rod furthest from the driver is on an angle is assembled as it came apart .ie there is a plain shank that goes through a rubber push which then takes a washer and split...
  12. Stuff - WANTED
    Specifically for a 56 belair 6 cyl manual , but i am assuming this linkage is common to all the three Tri Chevys. I need some non wonky gear shift rods if any one has any since converting to auto or raceing etc.. Finding it difficult to adjust out the sloppy gear change resulting in Jamming...
  13. Stuff - WANTED
    Wiper linkage needed for '75 Camaro. The wiper motor is there, we need the bits that link it to the wipers. Cheers Dusty
  14. Tech Features
    Anyone got any bright ideas? I have installed a C4 in my 55 Ford Customline. It originally had a 2 speed Fordomatic and I want to keep the column change. I have looked at Lokar shifters and it would appear that a solid linkage would be impossible to route, so it looks like a cable one is the way...
1-14 of 14 Results