Rods 'n' Sods - UK Hot Rod & Street Rod Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 97 Results
  1. Stuff - WANTED
    OK As the title says - complete motor and trans wanted for new project. Let me know what you have. I would even buy a car if it is sensibly priced. Prefer good condition - not needing recon. 350 /383 ci. Carb or injection. Thanks
  2. The Garage
    So after lots of lurking and learning I managed to source a half engine from the states for my project car. It's a 1974 four bolt main on standard bores and crank, and at first glance hadn't been run in a long long time. After its arrival I soon found why it had been pulled; head gasket...
  3. Stuff - FOR SALE
    Hi, I have 2 x 1 U.S. Gallons of Red Line 10-30 synthetic engine oil. Bottles are unopened. An excellent choice for your sbc and probably many other american V8's. This is a top rate oil, one of the best you can buy, retails at £58 per gallon, Have both for 60 quid cash, buyer collects from...
  4. Stuff - FOR SALE
    For sale: Located in Bedford... SBC reverse rotation water pump £10 - COLLECTION ONLY (heavy item, not worth me posting) Unsure how many miles it's seen, it was on my engine when I bought it which has not run yet. Mr Gasket Billet Aluminium Small Block Chevy Single Groove Crank Pulley...
  5. Stuff - WANTED
    Ideally I am after a non fuel injection running Chevy 305 that I can see running. However will consider 305,350 or a complete car that I can cannibalize if at the right price.
  6. Stuff - FOR SALE
    Crank #3932442 SBC £ 50-00 collection from luton / milton keynes
  7. Traders - For Sale / Services - CLOSED
    ONE PAIR OF ORIGINAL OLD SCHOOL SMALL BLOCK CHEVROLET MOROSO TALL GOLD ANODISED VALVE COVERS RUBBER GROMMETS FITTED NEW, NEVER BEEN FITTED, BOX IS A BIT TATTY BUT THE VALVE COVERS ARE EXCELLENT £60 PLUS SHIPPING SOLD Email...
  8. Stuff - FOR SALE
    Bought these in the States a few years back but never had a chance to fit them. Engine went in my '86 Camaro and we fitted an '88 engine with centre-bolted valve covers so these have just sat in a cupboard gathering dust. One of them got separated from it's packaging and has picked up a couple...
  9. Tech Discussion
    any help would be highly appreciated..... macharper
  10. Stuff - FOR SALE
    Edelbrock Victor Jr intake (model # 2975). Small welded repair to heater hose boss. £100. Proform 1-piece chromoly pushrods (+.100). Run for <100 road miles. £35. Boxed Carter 172gph mech. fuel pump (brand new). £85. Holley 4160 (vac. secondaries) 750 carb. Recent rebuild. Not been messed...
  11. Stuff - FOR SALE
    270 / 276 @ 0.050" Duration 106* LSA .625 / .625 Gross Lift RPM Range 4,400 - 8,200 Used, but very low hours and perfect. £120 + post.
  12. Stuff - FOR SALE
    270 / 276 @ 0.050" 106 LSA .625 / .625 gross lift Used, but low hours. Perfect condition. £150 ono.
  13. Tech Discussion
    Got a vacuum advance Mallory dual point in my sons coupe thats making a steady clicking noise, like the rotor arm's hitting the cap [bit like a elec fuel pump noise]. any one know what it could be? taken cap off and looks fine
  14. Stuff - WANTED
    I am looking for a 6-71 supercharger complete set up for a small block chevy ideally but would cosider blower on its own with few ancillaries. good money paid for the right thing. please ring john 07787770971 make an old guy very happy!!!!!!!
  15. Traders - For Sale / Services - CLOSED
    New SBC 383cid stroker pistons , hyperutectic .040 over , flat top 2 valve relief , floating pins for 6.00 long rods PRICE 155 to your door UK:D
  16. Stuff - WANTED
    Hi guys As title looking for a starter motor for a manual flywheel 153 tooth. Even if its knackered i only need the nose as they are interchangeable. Cheers Roland
  17. Stuff - WANTED
    sbc throttle linkage and cable wanted , the type that also holds the kick down cable for a th350 WHY ? Cheers Ash
  18. Tech Discussion
    Can you help ? My truck's got the running gear from a '77, plus an older Goodwrench motor. It came to me with old ramhorn manifolds (which have now been replaced by headers) and the p/s/pump was mounted on bodged bracketry. I've seen aftermarket brackets to use with headers, but anyone know...
  19. Stuff - WANTED
    Anyone got a 6 3/4" balancer for sale? Need it for my 327 I'm rebuilding. Can get one from Real Steel, but if anyone has one.............. 07766 465000 Thanks in advance
  20. Tech Discussion
    Hi all. I know I asked a similar question to this a few months ago asking about changing the rear crank seal on a sbc whilst the engine is in situ. To be honest I haven't gotten round to changing it yet hence the new enquiry. When changing these seals do they have to be replaced like for like...
1-20 of 97 Results
Top