Anyone clearing out their garage / retiring / giving up or whatever, and have any metalworking dollies, stakes, spoons, slappers, etc., available? The nearer to Oxford the better, especially for heavier pieces, but not essential.
Please PM on here, or call/text (including pics) to 07920 584324...
hi all i need a crank puller to get the belt pulley of the crank so i can carry on striping my engine think the tool would be universal but its for ford 4bolt thanks
Brand new never used still in the plastic bubble wrap, Mac Tools digital timing light model TL650E £100 plus £7.50 postage.
Cost new $350 or in UK £280
Just bought some Air Shears from Aldi. £12.99 cheap enough even if they don't last forever.
http://www.aldi.co.uk/uk/html/offers/2827_13375.htm
Check their other air tools that have just gone on sale today.
Steve
Does anyone out there have any 1/24th / 1/25th figures and garage tools, tool boxes that they no longer require?
I require these for a project diorama that i have been working on for a while. Please help.:(
Does'nt matter too much on condition of the figures, Steven Hawkins to Jodie Kidd it...
Are there such things as arch re radiusers? I mean for putting on the halfshaft nut on an axle and drawing a line to mark for enlarged arches. I saw one on the V8pop's V8pop thread on the NSRA forum, but I don't whether he purchased it or it was homemade. Do they exist? Any plans for a homemade...
advert on eurodragster . i dont know if this breaks any rules si ? if so please remove it , it just makes my blood boil and the more its about the better the chances of him getting it back , slim but worth a try
Date: 1/21/2010 4:48:38 PM Ref: 00093030
centerlines stolen!!!!!!!!!!!
hi, this...
16cfm piston compressor 3hp single phase motor, resevoir 150 litre ish in good working order this is an industrial model and not a diy version.
£295.
Appliance 10 by 15 rims suit jag pattern , painted but can be rechromed, £45pr
Radiator for rod brand new copper brass 5 staggered core , 29 by...
hi to all my mate is shuting up his spray shop in bromley he has lots of bits for sale 02084608427 julian, compressor twin motor £300 o.n.o, compressor single big tank £150 o.n.o, a big gas workshop heater that hangs from ceiling £500 o.n.o, hardly used 2 post car lift 3 phase you can change...
DRILL PRESS: A tall upright machine useful for suddenly snatching flat metal bar stock out of your hands so that it smacks you in the chest and flings your beer across the room, denting the freshly-painted project which you had carefully set in the corner where nothing could get to it.
WIRE...
Be warned it may be lengthy...............................:rolleyes:
This will help you make bends and curves in flat metal with common tools.
This is a 1 inch strip of 18 gauge cold roll 1008 series, notice the bottom that touches the bench is as flat and in full contact....
Now to create a...
Hammer: Originally employed as a weapon of war, the hammer nowadays is used as a kind of divining rod to locate expensive car parts not far from the object we are trying to hit.
Mechanic's Knife: Used to open and slice through the contents of cardboard cartons delivered to your front door...
looking for
a tailgate to suit a ford pick up... standard early pick up bed. anything considered to fill the void.
1960 mercury monterey offside rear body trim, blue tint glass, doors and maybe body cuts?
Also looking for a deep throat swager and 24-36" rollers?
oh and a steel dash to...
I sell brand new branded power tools as a side line and sell these through Ebay under user name tools2cheap if you see anything of intrest I would be able to sell it outside of Ebay a bit cheaper due to not have to pay the ebay fees. You can pay with Paypal or cheque whatever suits you best. And...
1st stab at this so trying to keep it simple and to the point. Rather than scenarios.
DO's
- Keep cords away from heat, oil, and sharp edges.
- Disconnect tools when not in use, before servicing, and when changing accessories such as blades, bits and cutting discs. Store in a dry place when...
giving up the workshop so i have a load of tools i dont really wanna have to store, have a look and see if theres anything your after :)
folding engine hoist, 2 years old, 0.5 - 2 ton
20 ton press, again only 2 years old
sealey supermig 150/5 inc reg, bottle etc
snap on scanner (2005...
.......for the time when a hammer just won't do:incheek:
The not so joyous task of pulling (pushing?) the top and bottom balljoints out.
Need a kit sharpish, any recommendations? The halfords/machinemart kit just ain't quite man enough for the job!