Rods 'n' Sods banner

work

  1. The Garage
    Here is a link to the car that I have been doing for the last few months. It needed quite a lot of work doing to it when I first saw it. Almost finished now just engine to put in and re trim and fit the interior. http://z14.invisionfree.com/rallysupport/index.php?showtopic=5045
  2. Chat
    With all the talk of this country being shite,people emigrating and the state of politics,you start to wonder if theres any future living here........ Working up on a roof today,sat on the ridge having a cuppa and a smoke and realised this countries not too bad :D
  3. Stuff - FOR SALE
    5 14inch ( i think) ford cosworth lattice work alloys for sale, 1 has puncture although it may just need resealing the tyres look in very good nick the alloys themselvs arent to bad paint peeling of on the inside but not on the outside been curbed in places useable though and im open to offers...
  4. Vehicles - FOR SALE
    Any one looking for a AUSTIN SOMERSET in need off work floor is all good bottom off doors need work but not a bad old thing Only looking for £250 pounds for it i will try get some pic on her so you can see it or just come and have a look :tup: My number is 07521900082
  5. Chat
    Got called in for a last minute jaunt round Europe on Monday (I'm writing this in Berlin) and wound up with about 4 hours to pack and get myself from Norwich to Rye to hop on a bus , not funny when its a 3.5 hour run on a good day and I was in Lowestoft when the call came :tdown: So there I am...
  6. On Topic
    ...now this will keep y'all going... http://www.kelloggautoarchives.com/gallery.html
  7. Traders - For Sale / Services - CLOSED
    I Recently moved into a bigger, more equiped premesis, I will be undertaking more complex work such as Roof chops,.. full or part chassis builds,.. chassis repairs and mods,.. custom suspension set ups,.. steering,.. full custom exhaust systems,... and any kind wheel mods, including...
  8. Chat
    hi , im after two steel bars machining and tapping to m18 x 1.25 tpi. the bars need to be 1 1/4" dia and the thread depths to 50mm , total length of each rod 180mm . is there anybody that could do these for me and at what cost . cheers ade
  9. Traders - For Sale / Services - CLOSED
    not sure if this is the right place, but just to let you know i'm in faversham, kent and can carry out custom/hotrod work for you. i've been building customs and hotrods part time for about 25 years now for myself and others. since dad passed away last october i am now working for myself...
  10. Stuff - FOR SALE
    Not really Rod related but here goes....... I have just bought a Mazda B2200 pick up for work and its fitted with a rather good nick Truckman top that i'm not gonna be using. I assume it'll go straight onto a single cab hilux,P100,Brava,Navara etc etc etc....but you might wanna check on it...
  11. The Garage
    I've owned my car for nearly 12 years now and, other than enforced periods, it's never been off the road for any great length of time. It never has been and never will be a show car, more a useable classic that I can improve/upgrade as time (and money) allows. Yes it has some rough edges, but...
  12. Chat
    for sidspop, some work photos first off, a 'mate' who is supposed to know better did this for me cock next dead mouse in a light fitting, only a baby tho fuse board burning out, never found the actual reason, but suspect it was due to overloading and wrong wire used as a fuse, i think...
  13. Tech Discussion
    Hi guys, im thinking of putting some slick 50 engine oil treatment into my 350 chevy motor, im not too sure on the correct mileage. Would i be wasting my time if the engine has got high mileage ? Does this stuff have any good qualities for an engine that im not to sure on the history ? Any...
  14. Vehicles - WANTED
    After being made redundant twice last year and not working since October, I am going back to work in 2 weeks time.:D Need a reliable, economical car/van so I can do the 100 mile round trip 5 days a week!:tdown: I DON'T want to drive boring unless I have to, but ANYTHING considered as long as...
  15. Chat
    Just a little bit of tinkering, some paint here and there and it should come up loverly! Maybe you can polish a turd!:D http://uk.cars.yahoo.com/11012010/36/rare-sunken-bugatti-auction-0.html
  16. On Topic
    ....this'll liven your afternoon up...
  17. Chat
    Hello, Leading on from another thread, do you have stuff you've ordered sent to work? I have most of my bits sent to work now and when a package turns up there is a lot of quess' as to what it is, the one that is the most wrong gets the coffees. So far some of the weirdest things have been; A...
  18. Chat
    Thought I'd post it up here as it's not a job as such, but I need some work doing and would rather give it to somebody from the RnS community. I need a clutch doing on a hi-cube transit. Also needs some welding for it's MOT, and possibly front wings, arches and rear arches doing. I can provide...
  19. Vehicles - FOR SALE
    Righto, lets get this bit over with... IT IS NOT MY CAR, IT IS BEING ADVERTISED FOR A 'CUSTOMER', ALL I KNOW IS WHATS BELOW...!!! 1936 Morris 8, two door, supposed Daimler V8, viva front suspension, narrowed Volvo on a 4 bar with coil overs and discs, box section chassis from the rear up to...
  20. The Shelf
    heres a few of my got bored at work creations. all made from stainless steel crafted with nothing more than hammer grinder pliers and a good old tig set. (and a bead blaster and masking tape for the graphics)
Top